Skip to content
Tesla Model 3 and Model Y Lowering Guide: Lowering Springs, Coilovers and Camber Arms

Tesla Model 3 and Model Y Lowering Guide: Lowering Springs, Coilovers and Camber Arms

Lowering a Tesla Model 3 or Model Y closes the big wheel gap these cars leave the factory with, cuts a little body roll and makes the car look far more planted. Because both cars share most of their rear suspension design, the parts and the problems are very similar. This guide covers the three ways to lower a Tesla (lowering springs, coilovers and air suspension), what a lowered Tesla needs for alignment, and which supporting parts are worth buying at the same time.

Browse everything we carry for these cars in our Tesla suspension parts collection.

Lowering Springs vs Coilovers for a Tesla Model 3 and Model Y

Option How much drop Adjustable? Best for
Lowering springs Fixed drop set by the spring (about 21–35 mm on the sets we carry) No – ride height and damping stay fixed Daily drivers who want a cleaner stance on the factory dampers
Coilovers Adjustable range (up to 75 mm front / 70 mm rear on the C2 kit below) Ride height and damping Owners who want to choose their exact height and tune the ride
Air suspension / air struts Adjustable on the fly Yes, height changes from the cabin Show cars and owners who need to raise the car for driveways

Tesla Model 3 Lowering Springs and Model Y Lowering Springs

Lowering springs are the cheapest and simplest way to lower a Tesla. They replace the factory springs and keep the factory dampers, so the ride stays close to stock while the car sits lower. The sets we stock are vehicle-specific:

Always match springs to your exact model and drivetrain (RWD, AWD/Long Range or Performance), because spring rates and weights differ between versions.

Tesla Model 3 Coilovers

Coilovers replace the whole strut and spring with a threaded, height-adjustable assembly. You choose the ride height, and most kits also let you adjust damping. For the Model 3 we carry the MaXpeedingrods C2 coilovers with Eibach springs for the Model 3 AWD and the matching C2 coilovers for the Model 3 RWD. Key specs of the AWD kit:

  • Full set of four coilovers with Eibach progressive springs front and rear
  • Lowering range of 0–75 mm front and 0–70 mm rear compared with stock height
  • 24 levels of rebound damping adjustment
  • Spring rates of 8 kg/mm (448 lbs/in) front and 6 kg/mm (336 lbs/in) rear
  • Stainless steel shock bodies; aftermarket front top mounts, factory rear top mounts reused

Coilovers make sense if you want a specific height (for example to line up with a set of wheels and spacers) or plan to do the odd track day. If you only want to lose the wheel gap, springs are usually enough.

Lowered Tesla Model 3 and Model Y: Camber and Toe

When any car is lowered, the suspension arms change angle. On the Model 3 and Model Y the rear wheels pick up extra negative camber and the rear toe changes too. Left uncorrected, that shows up as wear on the inside edge of the rear tires. Fixed factory arms cannot be adjusted far enough, so most lowered Teslas need adjustable rear arms to get the alignment back into spec:

Whatever you buy, finish with a proper four-wheel alignment at your final ride height.

Sway Bar End Links on a Lowered Tesla

Fixed-length end links can leave the sway bar preloaded once the car is lowered, so it pushes harder on one side and the car feels different in left and right turns. Adjustable front stabilizer end links for the Model 3 and Model Y let you set the length with the car at ride height and the wheels loaded, so the bar sits without preload.

Wheel Spacers for a Flush Fitment

Once a Tesla is lowered, the factory wheels often sit tucked inside the fenders. 20 mm hubcentric wheel spacers for the Model 3 (5x114.3, 64.1 mm hub bore, forged 6061-T6 aluminum, lug bolts included) push the wheels out for a flush look. They are listed for the RWD and AWD Standard Range and Long Range cars, not the high-performance versions. Read our wheel spacers guide before choosing a thickness.

How to Lower a Tesla Model 3 or Model Y: Order of Work

  1. Decide on springs, coilovers or air based on how low you want to go and whether you need adjustability.
  2. Order adjustable rear camber and toe arms at the same time, so the car only needs one alignment.
  3. Install the springs or coilovers and let the springs settle for a few days of driving.
  4. Set adjustable end links at ride height with the wheels loaded.
  5. Get a four-wheel alignment, then add wheel spacers if you want the wheels closer to the fenders (re-torque after the first 25–50 miles).

FAQ

Can you lower a Tesla Model 3?

Yes. Lowering springs, coilovers and air suspension kits are all made for the Model 3. Match the parts to your exact drivetrain, because RWD, AWD and Performance cars use different parts.

Do lowering springs work on the Tesla Model Y?

Yes. Model Y-specific springs, such as the Megan Racing set listed at a 30 mm front and 24 mm rear drop, replace the factory springs and keep the factory dampers.

Do I need camber arms after lowering my Tesla?

Most lowered Model 3 and Model Y cars pick up extra rear negative camber and a change in rear toe. Adjustable rear camber and toe arms let an alignment shop bring both back into spec and protect your tires.

Are coilovers or lowering springs better for a Tesla?

Springs are cheaper and keep a near-stock ride. Coilovers cost more but let you choose the exact ride height and damping. For a daily driver that just needs the wheel gap gone, springs are usually enough.

Leave a comment

Your email address will not be published..

Cart 1