Wheel spacers are one of the cheapest ways to change how a car sits. A pair of spacers pushes the wheels out toward the fenders for a flush stance, clears big brake calipers or coilovers, and can fix the "sunken wheel" look without buying new wheels. They also get a lot of bad press online. This guide explains what wheel spacers do, the difference between hubcentric and lug-centric and slip-on and bolt-on designs, whether wheel spacers are safe, and how to pick the right thickness.
Browse every size and bolt pattern we carry in our wheel spacers collection.
What Do Wheel Spacers Do?
A wheel spacer is a machined disc, usually aluminum, that sits between the hub and the wheel. It moves the wheel outward by the spacer's thickness. In practice that means:
- Wider track and flush fitment. The tire sits closer to the fender lip, which is the main reason most people buy them.
- Clearance. Spacers can stop a wheel from rubbing on a big brake kit, a coilover body or a suspension arm.
- Lower effective offset. A 20 mm spacer on a +40 mm offset wheel behaves like a +20 mm offset wheel. The wheel itself does not change.
Spacers also change the scrub radius and add a small amount of leverage on the wheel bearing, so bigger is not always better.
Types of Wheel Spacers: Slip-On vs Bolt-On
| Type | Typical thickness | How it mounts | What to check |
|---|---|---|---|
| Slip-on spacer | About 3–12 mm | Slides over the factory studs; the wheel bolts on through it | You usually need longer wheel studs or bolts so enough thread is engaged |
| Bolt-on (stud-on) spacer | About 15 mm and up | Bolts to the hub with the factory lug nuts; has its own pressed-in studs for the wheel | Torque the spacer to the hub first, then mount the wheel |
| Wheel adapter | Usually 15 mm and up | Same as bolt-on, but the outer bolt pattern differs from the hub | Lets you run a wheel with a different bolt pattern (for example 5x100 to 5x114.3) |
Hubcentric Wheel Spacers vs Lug-Centric
Hubcentric wheel spacers have a center bore that fits the car's hub exactly and a lip on the outside that matches the wheel's center bore. The wheel centers on that lip just like it would on the hub, so the weight of the car sits on the hub instead of on the studs. This is what most cars want and what we recommend.
Lug-centric spacers have a bigger, generic center hole and rely on the lug nuts to center the wheel. They are cheaper but more prone to vibration if the wheel is not centered perfectly.
If your aftermarket wheels have a bigger center bore than your hub, a set of aluminum hub-centric rings fills the gap. They come in common sizes such as 73.1–57.1, 66.6–57.1 and 67.1–60.1 mm (outer to inner), so you can match your wheel bore to your hub bore.
Are Wheel Spacers Safe?
Quality wheel spacers that are the correct size and installed correctly are widely used on street and track cars. Most problems people blame on spacers come from installation, not the part itself. The things that matter:
- Material. Forged or billet 6061-T6 aluminum is the common standard for quality spacers.
- Hubcentric fit. The spacer should match both your hub bore and your wheel bore.
- Thread engagement. With slip-on spacers, make sure the studs are long enough. If they are not, use extended studs or bolts.
- Flush contact. The back of the spacer must sit flat against the hub, with no rust, paint or debris in between.
- Torque and re-torque. Torque with a torque wrench, not an impact gun, and re-check the torque after the first drive.
Spacers do add some extra load on wheel bearings and change steering feel slightly, especially with very thick spacers. Use the thinnest spacer that gets you the fitment you want.
Wheel Spacers Pros and Cons
| Pros | Cons |
|---|---|
| Flush, wider stance without new wheels | More load on wheel bearings, especially with thick spacers |
| Clearance for big brakes and coilovers | Can cause rubbing on fenders if you go too wide |
| Wheel adapters let you run a different bolt pattern | Slip-on spacers may need longer studs |
| Cheap compared with new wheels | Needs careful install and periodic torque checks |
How to Choose Wheel Spacer Thickness
- Measure the gap. With the car on the ground, measure from the outer face of the tire to the fender lip. That is roughly how much room you have.
- Allow for suspension travel. Leave a few millimeters for compression and steering lock, especially on lowered cars.
- Match bolt pattern, center bore and thread pitch. All three must match your car. Wheel adapters are the exception for the outer bolt pattern.
- Pick the type. Thin sizes are usually slip-on; about 15 mm and thicker are usually bolt-on.
Example: Tesla Model 3 Hubcentric Wheel Spacers
The Tesla Model 3 is a good example of a car that looks better with spacers, because the factory wheels sit well inside the arches. We stock several 20 mm hubcentric sets for it:
- 20 mm hubcentric wheel spacers for the Tesla Model 3: forged, CNC machined 6061-T6 aluminum, 5x114.3 bolt pattern, 64.1 mm hub bore, M14x1.5 thread, 10.9 grade studs, black hard anodized. Sold as a pair with lug bolts for mounting the spacers. Torque spec 100–110 ft-lb. Fits Model 3 RWD and AWD, Standard Range and Long Range; not listed for the Performance versions.
- 20 mm aluminum hubcentric wheel spacer kit for the Model 3: 6061-T6 aluminum, anodized black.
- 20 mm hubcentric wheel spacers, 5x114.3: 6061-T6 aluminum, listed for the Model 3.
How to Install Wheel Spacers
- Loosen the lug nuts, lift the car safely and support it on jack stands.
- Remove the wheel and clean the hub face of rust and debris.
- For bolt-on spacers, fit the spacer to the hub and torque the nuts or bolts that hold it to the hub to spec in a star pattern.
- Check the spacer sits completely flush with no gap.
- Mount the wheel on the spacer's studs and torque the wheel nuts to spec.
- Re-torque everything after a short drive. The Model 3 spacers above call for a re-torque after 25–50 miles and again at 2,000–3,000 miles.
Wheel Spacers FAQ
Do wheel spacers affect alignment?
They do not change camber, caster or toe settings, but they do change the scrub radius, which can change how the steering feels.
Do I need longer studs with wheel spacers?
Usually with slip-on spacers, yes. Bolt-on spacers come with their own studs, so the factory studs only hold the spacer to the hub.
What is the difference between wheel spacers and wheel adapters?
A spacer keeps the same bolt pattern. A wheel adapter changes it, so you can run wheels drilled for a different pattern.
Are hubcentric wheel spacers better?
Yes, for most cars. They center the wheel on the hub so the weight rides on the hub rather than the studs, which helps prevent vibration.
How often should I check wheel spacers?
Check the torque after the first drive and at each tire rotation or wheel removal.
Ready to set up your stance? Shop the wheel spacers collection, and if you are going wider with bodywork too, read our fender flares guide.