Why Your BMW's Rear Floor Needs Structural Reinforcement for Track and Drift
Every high-performance BMW driver eventually discovers the same uncomfortable truth: the factory rear floor simply isn't engineered for the sustained forces of track driving, drifting, or aggressive street acceleration. When you're running true coilovers, launching hard off the line, or holding a drift through multiple corners, your rear subframe mounts and shock towers experience forces far beyond what a standard floor pan can safely handle. Over time, this stress leads to cracks in the floor metal, broken welds at the shock towers, and a chassis that flexes excessively under load—all of which kill handling precision and reliability. The BMW Rear Floor Subframe to Shock Tower Brace solves this problem by adding structural reinforcement at the exact locations where BMW Motorsport engineers reinforced the factory E46 GTR and touring car shells, allowing your chassis to handle the punishment of modern drift and racing without developing stress fractures.
The difference between a reinforced rear floor and an un-braced setup becomes obvious the first time you feel your suspension geometry hold consistent under load. Factory floor pan deflection isn't something you necessarily see—it's something your tires and suspension geometry feel. When your rear subframe points flex downward during hard acceleration, your suspension geometry changes unpredictably, your chassis loses grip, and your feedback from the road disappears. A properly reinforced floor pan using the BMW Rear Floor Subframe to Shock Tower Brace locks the rear floor rigidly in place, so every adjustment you make to your suspension geometry stays true, and your car responds exactly how you've tuned it to respond.
This article breaks down exactly what a rear floor subframe brace does, how to install one on your E36 or E46, and why this single upgrade often delivers more noticeable improvement than suspension geometry changes alone. If you're building a drift car or track BMW, understanding and implementing rear chassis reinforcement is non-negotiable for performance, longevity, and safety.
How BMW Motorsport Designed the Reinforcement Strategy
BMW's factory motorsport division has been reinforcing rear chassis structures since the E30 M3 era, but their most refined approach came through the E46 GTR and factory touring car programs. These race cars endured sustained high-speed cornering, rapid gear changes under load, and repeated brake-and-accelerate cycles that stress the rear floor in ways normal street driving never does. The engineers at BMW Motorsport discovered that simply adding diagonal braces or thicker floor steel wasn't the answer—the key was creating a load-distribution path that spreads stress across multiple points instead of concentrating it at the subframe mounts. By connecting the rear floor to the shock towers and then tying everything back to the subframe area with a cross-brace structure, they could handle extreme torque loads, prevent localized cracking, and maintain chassis rigidity even after repeated track sessions.
The SLRspeed version of this design follows BMW Motorsport's proven engineering approach, using the same load-path strategy that worked on race cars. Rather than just thickening the floor or adding heavy steel plating, the brace creates a triangulated structure that distributes forces efficiently. When you accelerate hard and your differential applies torque through the subframe, that force is no longer concentrated at the four subframe mounting bolts—instead, it's distributed across the entire braced structure and then transferred to the shock towers and floor pan in a way that minimizes localized stress. This is why you see the factory race cars running braces like this, and why E36 and E46 drift and road-race cars that push real performance numbers need them too.
The manufacturing process matters here too. The SLRspeed brace is manufactured and assembled in the USA using aerospace-grade aluminum and high-strength steel, not mild steel or stamped components. Aerospace-grade aluminum provides superior strength-to-weight ratio compared to factory floor steel, which means the brace reinforces without adding significant mass to the rear of your car. High-strength steel components at stress points handle the repeated loading cycles without fatigue, and the threaded tube construction allows secure bolting without welding—a crucial advantage if you ever need to remove or replace the brace for maintenance.
Four Key Functions: Floor Reinforcement, Shock Support, Differential Notching, and Torque Distribution
The BMW Rear Floor Subframe to Shock Tower Brace isn't a single-purpose piece; it performs several critical functions simultaneously, which is why it becomes an essential component once you start upgrading your suspension or differential. Understanding each function helps you see why this brace deserves a spot on your build list, even before you install true coilovers or a quick-change differential.
Rear Floor Reinforcement and Stress Crack Prevention: Factory floor pans develop stress cracks at subframe mount locations after sustained track use or aggressive driving. These cracks typically appear in a small radius around where the subframe bolts attach—a zone of high stress concentration. Once a crack starts, it propagates quickly because each acceleration cycle flexes the floor slightly, opening the crack further. The brace spans across the subframe mounting area, distributing the force that would normally concentrate at each individual bolt hole across the entire width of the brace structure. This dramatically reduces local stress at each mounting point, preventing the micro-fractures that lead to visible cracks. On E36s and E46s that see frequent track time or aggressive acceleration, this function alone justifies the cost within the first year of ownership.
Rear Shock Tower Reinforcement for True Coilover Installations: Factory shock towers on E36 and E46 BMWs are designed for OEM suspension loads—the gentle up-and-down motion of street driving. True coilover setups place much higher and more frequent loads on these towers. Every hard launch, every sustained cornering cycle, every dive under braking puts vertical and lateral load directly onto the shock tower weld. Over hundreds or thousands of cycles, this repeated loading causes the weld to crack or the surrounding floor metal to tear. A properly designed shock tower reinforcement brace adds a second load path, so the coilover force is shared between the factory weld and the brace structure. This reduces stress on the original weld by 30–50%, depending on setup, and effectively doubles the service life of the shock tower connection. If you're running true coilovers and haven't reinforced your shock towers, you're essentially gambling on how long your welds will hold.
Lateral and Longitudinal Reinforcement for Quick-Change Differential Installations: Quick-change differentials require you to notch the factory floor crossbeam—you have to cut metal away to make room for the differential case. This notching removes a structural element, creating stress concentrations on both sides of the cut. Without reinforcement, the floor around the notch acts like a stress riser in metal fatigue analysis; cracks will eventually initiate near the edges of your notch and propagate outward. The brace provides both lateral and longitudinal reinforcement, effectively replacing the structural capacity of the notched section and distributing the stresses away from the cut edges. For anyone running a quick-change diff, this brace is as essential as the diff itself—it's your insurance policy against developing a cracked floor after a year of aggressive driving.
Torque Load Distribution and Subframe Flex Control: When you're accelerating hard and your differential is applying torque through the subframe, the rearward points of the subframe mount experience a strong downward pull. This causes the rear floor to flex downward at the subframe mounting area, which changes your suspension geometry in real-time. Camber curves suddenly, your wheel loses some contact patch, and your grip disappears mid-corner. The brace prevents this rearward-and-downward movement by creating a rigid structure that ties the subframe mounting area to the shock towers. Instead of allowing the floor to deflect, the brace distributes torque through multiple load paths. This means your suspension geometry stays consistent, your grip remains predictable, and your handling feedback is sharp and immediate. On drift cars, this translates to more confidence and control through sustained slides; on road-race cars, it means faster lap times and less tire wear from changing geometry.
E36 vs. E46 Installation: What's Different and Why It Matters
Both E36 and E46 BMWs benefit from the same structural reinforcement strategy, but the factory design differences between these generations create slightly different installation procedures. Understanding these differences helps you plan your installation time and set realistic expectations for your particular car.
E36 Installation Advantage: Factory-Marked Mounting Points: The E36 generation has two metal protrusions already welded to the factory floor pan in exactly the right locations for rear floor bracing. These protrusions aren't random; they're part of the OEM design, positioned where stress concentrations naturally occur. On your E36, you simply identify these two protrusions (they're obvious once you get under the car), mark them with a center punch, and drill through them using a 12-inch drill bit. The holes then align perfectly with the threaded tubes on the brace structure, eliminating any guesswork about positioning. No subframe drop is necessary—you can complete a basic E36 installation in 1–2 hours with the car supported on jack stands and good lighting underneath. This straightforward process is one reason why E36 drift builds are so popular; the factory floor design seems almost optimized for aftermarket reinforcement.
E46 Installation: Measured Positioning and Optional Subframe Drop: The E46 generation doesn't have pre-welded protrusions marking ideal mounting points. Instead, you need to measure from reference points on the subframe and floor pan using your factory service manual dimensions. This requires more care and preparation, but it's still entirely manageable for someone comfortable with basic measurements. You'll mark two points on the floor based on factory reference dimensions, then drill with a 12-inch drill bit just as you would on an E36. The advantage here is that a 12-inch drill bit is long enough to access the mounting holes even without dropping the subframe, though many shops choose to drop the subframe anyway because it provides much better access and visibility. If you drop your subframe on E46, your installation time increases to 2–3 hours total, but you gain the peace of mind of perfect positioning and the ability to inspect subframe mounting conditions while you're there.
The 12-inch drill bit specification is crucial on both generations. A standard 6–8 inch drill bit won't reach through the floor pan and into the brace mounting area; you specifically need a 12-inch bit designed for deep drilling. These bits are inexpensive (typically $15–30) and worth buying new rather than using a old dull bit that might wander or bind during drilling. If you don't have a drill with the power to handle a 12-inch bit (which can bind significantly), consider using a smaller machine shop to drill these holes—the $50–75 cost is worth eliminating the risk of a botched hole location.
Installation Hardware and Fastening Options
The brace ships with hardware to bolt directly into the rear floor and subframe threaded tubes, giving you flexibility in how you finalize the installation. This matters more than it might seem, because your floor pan condition and previous modifications affect which fastening method works best for your particular car.
Standard Threaded-Tube Bolting: The brace has M12 threaded tubes welded into its structure. The shipped hardware allows you to insert M12 bolts directly into these threaded tubes from above (through your drilled floor holes), then tighten them down like a standard bolt-and-hole connection. This method works perfectly if your floor pan is in good condition and you don't have subframe access needs. It's the fastest and cleanest installation approach, typically taking 20–30 minutes once holes are drilled. The trade-off is that you can only access the bolt heads from above; if you ever need to service the brace or subframe, you have to remove these bolts, which might involve cutting or careful leverage work.
Through-Bolt Configuration with All-Thread: For builds where you want full accessibility or where your floor pan is damaged around the threaded-tube areas, you can supply your own M12 all-thread rods (threaded rod material, available at any hardware store or online for $2–5 per rod). You feed the all-thread through the floor holes, through the brace mounting holes, and out the bottom. Then you thread M12 nuts onto the all-thread from underneath, add lock washers to prevent loosening from vibration, and tighten progressively to seat the brace evenly. This method takes longer (45–60 minutes to tighten properly and evenly), but gives you the advantage of accessing fasteners from underneath if you need to remove or adjust the brace later. This option is especially useful if you're planning a quick-change differential installation and anticipate needing to access the rear floor multiple times during your build sequence.
Whichever fastening method you choose, use M12 Grade 8 bolts or all-thread and tighten to approximately 30–40 ft-lbs (40–55 Nm) using a torque wrench. This specification is conservative but appropriate for threaded connections in aluminum; over-tightening can strip threads or crack the brace if it's aluminum-reinforced. After your initial installation and after your first track session, re-check all fasteners, as vibration can occasionally loosen bolts during break-in. Apply threadlocker (Loctite 243 medium-strength for semi-permanent holding) to bolt threads before final tightening to prevent vibration loosening during sustained track use.
Real-World Performance Gains and Chassis Dynamics
The performance improvements from adding rear floor reinforcement are measurable and noticeable from your first few minutes of driving after installation. Chassis-dynamics changes aren't as dramatic as suspension geometry changes (you won't suddenly gain 5 degrees of camber), but they're more immediately obvious than you might expect because they affect how your car feels under every input.
Improved Handling Feedback and Cornering Precision: With your rear floor braced, your suspension geometry stays consistent throughout a cornering cycle. Your camber, ride height, and wheel geometry don't shift mid-corner because the floor isn't deflecting under load. This means your tires load and unload predictably, your grip builds smoothly as you increase steering angle, and your feedback from the road is sharp and immediate. Drivers typically describe this as the car feeling "locked in" or "solid" compared to the pre-brace setup. On a drift car, this translates to being able to feel exactly when your rear tires are about to break loose, making your slide progression more controlled. On a road-race car, it means more consistent lap times and faster corner exit speeds because you're not losing grip mid-corner due to changing geometry.
Reduced Tire Wear and Extended Tire Life: Floor flex causes uneven tire loading during cornering, which accelerates edge wear and creates uneven wear patterns. When your floor is rigid and your geometry consistent, your tire loads evenly across its contact patch. This extends tire life by 20–40% depending on your driving style and track conditions. For track drivers running multiple sessions per weekend, this can save $500+ per season in tire costs alone. On drift cars, the more consistent geometry also reduces the wear-and-slip ratio on drift tires, letting you get more passes out of a single set before the inside shoulder is too worn for clean driving.
Increased Driver Confidence in Sustained High-Speed Driving: When your chassis flexes, you can feel it. The steering feels slightly delayed, the car seems to wander slightly in tight corners, and overall you never feel fully confident pushing hard. Once your chassis is rigid, you feel the difference immediately—the steering response is crisp, the car points exactly where you're aiming, and corner entry feels predictable and solid. This confidence translates to faster driving times naturally because you're willing to carry more speed into corners and trust the grip more. For many drivers, this psychological benefit (knowing your chassis is solid and won't surprise you) is worth as much as the objective performance gain.
Durability and Crash Survivability: A rigid chassis is also a safer chassis. In an accident or track incident, a chassis that flexes excessively absorbs energy unpredictably and can collapse in unexpected ways. A braced chassis distributes impact forces through multiple load paths, protecting the occupant compartment more effectively. While no aftermarket brace will make your car as strong as a full roll cage, the improved structural rigidity does provide marginal but real safety benefits in a side impact or corner strike scenario.
Compatibility with Other SLRspeed Chassis Upgrades
The rear floor subframe brace plays well with other chassis modifications, and in fact, your other upgrades influence how much benefit you'll get from the brace. If you're building a comprehensive drift or road-race setup, the brace becomes even more valuable when combined with control arm upgrades, sway bar improvements, and steering angle kits.
Control arm upgrades (whether tubular replacements or bushing inserts) change how suspension loads are transferred through the chassis. When you add stiffer control arm bushings or switch to adjustable front control arm bushing lollipops, you're concentrating more load through specific points. A braced rear floor distributes these loads more evenly, preventing stress concentration that might otherwise develop. Similarly, if you're running upgraded sway bars or adjustable sway bar links, the lateral forces during cornering are transmitted more aggressively to the floor pan. The rear floor subframe brace handles these increased lateral loads without deflecting, maintaining the suspension travel you've carefully tuned with your geometry adjustments.
For E36 and E46 models running an SLR steering angle kit (which increases your steering lock and sharpens your turn-in response), the improved cornering precision that comes from a rigid rear floor amplifies the benefits of your upgraded steering. You're now able to feel exactly how much steering angle you're carrying into each corner, and your rear end responds consistently to your steering inputs because the floor isn't flexing and changing your rear suspension geometry mid-maneuver. The combination of steering upgrades plus chassis bracing is substantially more effective than either upgrade alone.
Common Installation Mistakes and How to Avoid Them
Most installation issues come from rushing the drilling phase or not securing fasteners properly during initial setup. A few hours of careful work prevent months of frustration and potential safety issues.
Drilling Misalignment and Hole Placement Errors: The most common mistake is drilling holes that aren't perpendicular to the floor pan, which causes the brace to sit at an angle. When the brace isn't level, fasteners experience shear loads instead of pure tension, which accelerates loosening and can eventually cause bolt failure. To avoid this, use a magnetic drill guide or drill press jig to ensure your 12-inch drill bit enters the floor at exactly 90 degrees. On E36, the factory protrusions guide your drill, so this is less of an issue. On E46, take extra time to mark your hole locations precisely using a center punch and verify with a straight edge before drilling. If your holes end up misaligned, don't force the brace into place—drill new holes in a slightly different location rather than bending or forcing the structure.
Under-Tightening and Vibration Loosening: Many builders tighten fasteners just enough to "feel snug" without using a torque wrench. In the harsh vibration environment under a car, snug isn't enough. Bolts that should be at 35 ft-lbs but are only tightened to 20 ft-lbs will gradually work loose. This shows up as rattles or creaks under acceleration after the first few track sessions. Always use a torque wrench set to 30–40 ft-lbs and always apply threadlocker compound to threads before final tightening. Check fasteners again after your first track session and after every 4–5 track sessions for the first month—this catches any loosening before it becomes a problem.
Omitting the Threadlocker Step: Threadlocker (Loctite 243 is appropriate for automotive use) prevents bolts from loosening under vibration without making them permanent. Many builders skip this step to save $5 or because they're unfamiliar with the product. Don't. Threadlocker adds maybe 5 minutes to your installation and prevents 100% of bolt-loosening issues. Once you apply it and let it cure (check the package—Loctite 243 typically cures in 24 hours), your fasteners are locked in place but can still be removed with normal tools if future service is needed. It's a no-downside addition to any bolted automotive installation.
Improper Through-Bolt Tightening (If Using All-Thread Method): If you're using the through-bolt configuration with all-thread, tighten bolts gradually and progressively in an X pattern (tighten one bolt a quarter-turn, then the bolt diagonal to it, then repeat) rather than fully tightening one bolt before moving to the next. This ensures the brace sits evenly and doesn't tilt or bind. If you fully tighten one fastener before tightening others, the brace might bend slightly, causing the remaining holes to misalign and making final tightening difficult. Progressive tightening takes an extra 10 minutes but ensures proper seating and prevents structural stress on the brace.
Long-Term Maintenance and Durability Expectations
Once properly installed and fastened, a rear floor subframe brace requires minimal maintenance. Aerospace-grade aluminum resists corrosion far better than factory steel, and the bolt connections are the only wear points you need to monitor.
Bolt Inspection Schedule: Check all fasteners every 6 months or after every 10–15 track days, whichever comes first. Use a socket wrench to verify that each bolt is still at spec (30–40 ft-lbs); if you find loose bolts, re-tighten and re-apply threadlocker. This inspection takes 15 minutes and prevents the catastrophic failure scenario where bolts loosen gradually until the brace moves or fractures.
Corrosion Prevention on Steel Components: If your brace includes steel reinforcement sections (many designs use a combination of aluminum and steel for optimal strength-to-weight ratio), inspect these areas annually for surface rust. Light surface rust is cosmetic and not a structural concern, but heavy rust can weaken steel over time. If you see significant corrosion, wire-brush the affected area and apply a high-temp automotive paint or clear coat to prevent further oxidation. The SLRspeed brace uses aerospace-grade materials selected for corrosion resistance, so this is rarely a concern, but it's worth monitoring if your car sits outdoors or lives in a corrosive environment (salt air, high humidity).
Floor Pan Condition Changes After Installation: Over years of aggressive driving, your floor pan might develop new stress cracks in areas not directly covered by the brace. This is normal and expected—the brace eliminates cracks in the critical subframe mounting and shock tower areas, but other regions of the floor still experience stress. If new cracks appear elsewhere, they're usually slower-developing and less critical than pre-braced cracks. You can address these with localized patches or welded reinforcement as needed. Document the condition of your floor when you install the brace so you can compare and understand how your build is aging over time.
Integrating Rear Floor Bracing into Your Overall Build Strategy
For builders planning a comprehensive E36 or E46 drift or road-race build, rear floor bracing shouldn't be an afterthought—it should be part of your fundamental chassis plan. If you're going to invest in true coilovers, control arm upgrades, and suspension geometry adjustments, protecting that investment with a rigid chassis is essential. The cost of a rear floor subframe brace ($400–600 depending on material options and your location) is trivial compared to the cost of repairing stress cracks, re-welding shock towers, or diagnosing mysterious handling changes caused by chassis flex.
A recommended build sequence for E36/E46 drift or track cars is: (1) Chassis bracing first, including rear floor subframe bracing. (2) Control arm and suspension component upgrades. (3) Steering angle kit and geometry adjustments. (4) Coilover installation and final setup. This sequence ensures your chassis is solid before you start stressing it with upgrades, and it means every geometry adjustment you make stays true because your chassis isn't flexing beneath your suspension.
If you're building on a budget and need to prioritize, rear floor bracing comes before cosmetic upgrades and even before some suspension geometry changes. A well-braced factory-suspension BMW handles more predictably than a poorly-braced car with expensive coilovers. Build solid, and the rest of your build will be more effective.
Ready to Build a Solid Rear End
Chassis rigidity is the foundation that every other modification rests on. Without a solid floor and properly supported shock towers, your suspension geometry drifts during driving, your tire loads vary unpredictably, and your handling feels inconsistent no matter what else you upgrade. The BMW Rear Floor Subframe to Shock Tower Brace solves this problem using a design proven on BMW Motorsport race cars, engineered for E36 and E46 platforms, and manufactured right here in the USA. Whether you're building a track-day weapon, a weekend drift car, or a street car that sees serious driving, adding rear chassis bracing is one of the highest-value chassis modifications you can make. The installation is straightforward, the fastening options are flexible for different floor conditions, and the performance payoff is immediate and noticeable. Explore the brace, plan your installation, and give your chassis the rigidity it needs to handle what you're going to throw at it.
| Area | Stock Factory Floor | With Rear Floor Subframe Brace |
|---|---|---|
| Subframe Mount Stress | Factory floor flexes under torque loads, causing stress cracks to develop at subframe mounting points after 1–2 years of track or drift use. | Brace distributes torque loads across a wider area, preventing stress cracks and extending subframe mount longevity indefinitely with proper maintenance. |
| Coilover Shock Support | Factory shock towers are not reinforced for true coilover installations; repeated coilover cycles eventually crack tower welds and surrounding floor metal. | Reinforced shock tower connection handles sustained coilover loads during aggressive track sessions and drift runs without weld cracking or metal fatigue. |
| Differential Notching | Cutting the factory floor crossbeam for quick-change differentials compromises nearby structural points, requiring expensive additional bracing elsewhere. | Brace provides complete lateral and longitudinal reinforcement for notched sections, eliminating the need for supplementary floor-pan patches. |
| Torque Load Distribution | Rear subframe points pull downward during hard acceleration, causing localized floor flex and inconsistent handling feedback through the chassis. | Brace prevents downward movement of rear subframe points, reducing overall floor flex and delivering more responsive, predictable handling characteristics. |
| Installation Time | Traditional chassis bracing often requires dropping the subframe and extensive drilling work, consuming 4–6 hours of labor. | E36 installation takes 1–2 hours with no subframe removal; E46 takes 2–3 hours with optional subframe removal, significantly faster than traditional methods. |
| Material Quality | Factory floor is mild steel with minimal reinforcement; prone to rust in areas exposed to salt or moisture from track environments. | Brace is manufactured from USA-assembled aerospace-grade aluminum and high-strength steel, engineered for long-term durability and corrosion resistance. |
How to Install the BMW Rear Floor Subframe to Shock Tower Brace
- 01 · Gather tools and hardware. Collect a 12-inch drill bit, drill with adequate power, socket set for M12 bolts or all-thread, a floor jack and jack stands, safety equipment, and the brace with included hardware. For E36, you'll use the pre-drilled metal protrusions on the factory floor as your guides. For E46, have a measuring tape and the factory service manual dimensions ready so you can locate mounting points accurately.
- 02 · Lift and support the vehicle (E46 optional). Raise the rear of your BMW on a hydraulic jack and secure it with jack stands under the frame rails—never work under a vehicle supported only by a jack. While E36 installation can happen without dropping the subframe, raising the car gives you clearance to access the underside and position the brace comfortably. For E46, lift the car and remove the subframe if you prefer better access; subframe removal is optional but makes drilling and bolt installation easier.
- 03 · Locate and drill mounting holes (E36 method). On E36, identify the two metal protrusions on the rear floorboard near the subframe mounting area. Position your 12-inch drill bit at each protrusion and drill through the floor pan at those factory-marked points. The holes will align perfectly with the threaded tubes built into the brace, eliminating guesswork and ensuring the brace sits at the correct height and angle for optimal load distribution.
- 04 · Locate and drill mounting holes (E46 method). On E46, use a measuring tape and your service manual to locate the subframe mounting points and shock tower attachment zones. Mark these points with a center punch to prevent drill bit wandering, then carefully drill with your 12-inch drill bit through both the floor pan and any factory reinforcement. Take your time on E46 to ensure holes are perpendicular to the floor and aligned with the brace's threaded mounting tubes.
- 05 · Position and bolt the brace in place. Insert the brace through the access holes from underneath the vehicle, threading the M12 bolts through the floor pan and into the brace's threaded tubes. Hand-tighten all bolts first to ensure the brace is centered and level, then use a socket and torque wrench to tighten to manufacturer spec (typically 30–40 ft-lbs for M12 Grade 8 bolts). If using the through-bolt option with all-thread, install all-thread rods, add lock washers and nuts from underneath, and tighten progressively to avoid bending the brace.
- 06 · Verify alignment and load test. Once all bolts are tight, check that the brace is not twisted and sits evenly against the floor pan and shock tower reinforcement points. Lower the vehicle slowly and check clearances between the brace and fuel tank, brake lines, and other components. Take the car for a short test drive at moderate speed, listening for any rattles or creaks that might indicate loose bolts. Return to the shop, re-check all fasteners, and apply threadlocker (Loctite 243) to prevent vibration loosening over time.
Without this reinforcement, repeated coilover cycles can cause stress cracks to develop at the shock tower welds over time, which is exactly why BMW Motorsport designed this brace for their factory race cars.